Water temperature sensor for paramotor FlyHenry PPGmeter

PPG Meter from Fly Henry - The Paramotor Instrument with a Huge Safety Advantage New functions of the 2024 model: - Flight time calculation depending on the fuel level (the tank level sensor and flow sensor are required for this, both of which are also available here in the shop) - Reset all timers - Possibility to set the initial time in the total time meter - Possibility to lock the total time meter with a code You will find the technical data further down the page after my text Many instruments can now measure RPM or display the cylinder head or exhaust gas temperature.The PPG Meter is also supplied in the standard version with an RPM sensor and a sensor for measuring the cylinder head temperature under the spark plug (CHT). Additional sensors can optionally be connected, such as the EGT sensor for exhaust gas temperature, as well as sensors for measuring fuel flow or the fuel tank level. But the PPG Meter from Fly Henry offers another huge advantage: the Start Monitor System. Start Monitor System is a technology that monitors the engine RPM after starting and immediately switches the engine off if a certain RPM is exceeded.With the PPG Meter, you can individually define both the maximum RPM and the time during which it must not be exceeded within a wide range. This allows the system to be individually adapted to each paramotor.Engines with Flash starters, for example, can sometimes reach slightly higher RPM for a short moment during starting than systems with a conventional starter or electric start. Here you can see in a short video how the system works. As most of you know, I myself had an accident in April 2016 in which the propeller of my engine, which I had started on the ground, seriously injured my arm.The cause of the unintended increase in RPM immediately after starting was a jammed Bowden cable. Of course, you can say "that won't happen to me because of xy". But there are so many reasons why an engine can unexpectedly rev up when starting, whether due to a technical defect or accidentally applying throttle, forgetting to release the locking throttle..... Over the past few years, I have met many pilots who have had accidents like mine. Some are missing a finger, some have suffered a muscle laceration like I did back then, and one pilot had to have his arm amputated. These are not the nice topics we want to associate with our sport, and this is probably also the reason why they are so often pushed aside. For a long time, I felt the same way. Although I had been using a PPG Meter since 2019, I had never connected it completely or activated the Start Monitor System. The tragic fatal accident of a pilot I knew affected me deeply, and I realized that I had also neglected this issue. Therefore, after returning from Italy, the first thing I did was connect the system completely (it is actually not that difficult) and test it. And sure enough, it worked perfectly. When I applied throttle after starting the engine and exceeded the set RPM, the engine immediately shut down and an error message appeared on the display. After the defined waiting time, the engine can then be started again. Since the English operating instructions and the not entirely perfect installation instructions had been a hurdle for many pilots, I sat down and translated the operating instructions completely and documented the possible installation on the device.This should make it possible for every pilot to install the system on their paramotor and thereby drastically reduce the risk of injuries when starting the engine. Of course, you should never rely 100% on a system and must continue to carry out a proper pre-flight check. For me, the PPG Meter is like a reserve parachute. It also gives me no guarantee that nothing can happen to me, but it is a second chance to come out of a situation safely if I have already made mistakes. _________________________________________________________ The PPGmeter instrument offers the following functions: - Graphic display with orange backlight- RPM display- Start Monitor System – safety when starting the engine- 2 connections for temperature sensors up to 1200°C (e.g. CHT cylinder head and EGT exhaust gas temperature or water temperature)- Operating hours meter (up to 3 timers)- Operating voltage in V (either from the onboard battery or the battery box used)- Display of the fuel tank level when the sensor is installed- Maximum values – temperature, RPM, fuel flow rate (with the corresponding sensor)- Alarms – freely configurable for temperature, RPM, operating voltage, fuel tank level (with the corresponding sensor) Can be used with a voltage of 5-20V: - without a separate battery on paramotors with an onboard battery (e.g. with an electric starter)- with a separate battery of your choice, e.g. a box with AAA batteries or a 9V block battery or a small rechargeable battery pack...Possible accessories:EGT exhaust gas temperature sensorWater temperature sensorFuel tank level sensorFuel flow sensor Technical specifications: Power supply: 5-20V (If your engine does not have a battery, you can optionally use your own battery)Display module size: 60x37x15mmSensor module size (m

Fly Meter – The instrument for power paragliding and ULL New model 2024 New Functions: Calculation of flight time based on fuel level Reset of all timers Option to set initial time of the main timerOption to lock reset and set of main timer with a 4-digit code Fuel flow alarm (fuel leakage) - RPM alarm Oil and fuel pressure alarm - min. and max. Oil and water sensor 2x preset, 1x programmable sensor New oil and fuel pressure sensor 2 designs Functions: 4x temperature 0-1000°C CHT or EGT switchable display between °C and °F 1x temperature 0-125°C oil, water, etc., switchable between °C and °F 1x oil or fuel pressure measurementRPM meter 4x engine hours Service interval setting Fuel gauge fuel level in the tank Fuel flow meteractual and average consumption, total fuel consumed Calculation of flight time based on fuel quantity Measurement of on-board voltage Alarms - temperature, oil or fuel pressure min. and max., fuel level , on-board voltage min. and max., max RPM, max fuel flow Display contrast and backlight adjustment Safety Alarms:Configurable alarms notify the pilot of abnormal operating conditions and limit violations and problems.Fuel level and fuel flow alarmsOn-board voltage alarms Temperature alarms (minimum / maximum limits) Oil and fuel pressure alarms RPM limit alarmsThe instrument is divided into two modules: Sensing module – placed near engine Display module – placed on the dashboard These modules are connected by a thin data cable of standard length 280cm.The instrument is operated with two buttons: - ESC – escape Short press - always one step back, exit menu. Long press – approximately 2s deactivates display blinking for any alarm, the alarm remains highlighted only on the display by position highlighting. - ENT – enter Long press – used for basic entry into the menu, confirm entry into the selected position, or change the desired value. Short press – used to navigate between rows The control is intuitive, and the menu description on the display precisely guides you where you need to go. Technical specifications: Power supply: 7 - 20VDC Temperature 1 – 4: 0 - 1000°C Oil/water temperature: 0 - 125°C Oil/water pressure: 0 - 6.9 Bar (0 – 100 PSI) RPM Detection: 2-5 turns around the high-voltage cable to the spark plug – depends on the ignition type Display module: Front panel dimensions: 98 x 64 mm Panel hole dimensions: 93 x 59 mm Weight: 150g Measuring module: Base dimensions: 124 x 40 x 20 mmWeight: 100g  

Separater Abgas Temperatur EGT-Sensor für das PPG Meter von Fly Henry Technische Spezifikationen: Länge der Leitung zwischen EGT-Sensor (Abgastemperatur) und Stecker: 50cm (80cm Version auf Anfrage)Gewinde M8 x 1 mm Lieferumfang:EGT-Temperatur Sensor 50cm lang Benutzte oder bei der Montage beschädigte Sensoren können nicht umgetauscht werden. Wichtiger Hinweis:Da wir keinen Einfluss darauf haben, wie der Anwender das Fly Henry PPG Meter, sowie das damit verbundene Zubehör verwendet, übernehmen wir keine Haftung für Schäden die durch oder trotz der Benutzung des Fly Henry PPG Meter entstehen. Eine Genehmigung zur Nutzung am jeweiligen Fluggerät, z.B. einem Paramotor kann nur durch den jeweiligen Motoren-/Rahmenhersteller erteilt werden. Durch unautorisierte Nutzung können unter Umständen die Betriebserlaubnis für das jeweilige Fluggerät oder Gewährleistungsansprüche erlöschen. Das Start Monitor System befreit den Piloten nicht davon einen Vorflugcheck durchzuführen sowie weitere vorgeschriebene Sicherheitsvorgaben einzuhalten. Der Käufer des Fly Henry PPG Meter übernimmt die alleinige Verantwortung für alle Risiken, die mit der Benutzung verbunden sind, einschließlich Sachschäden, Verletzung und Tod des Nutzers sowie Dritten.

Separater CHT-Sensor für das PPG Meter von Fly Henry Technische Spezifikationen: Länge der Leitung zwischen CHT-Sensor (Zylinderkopftemperatur) und Stecker: 50cm (80cm Version auf Anfrage)Ringdurchmesser 14mm, 12mm od. 10mm Lieferumfang:CHT-Temperatur Sensor 50cm lang, Ringdurchmesser 14mm, 12mm od. 10mm Benutzte oder bei der Montage beschädigte Sensoren können nicht umgetauscht werden. Wichtiger Hinweis:Da wir keinen Einfluss darauf haben, wie der Anwender das Fly Henry PPG Meter, sowie das damit verbundene Zubehör verwendet, übernehmen wir keine Haftung für Schäden die durch oder trotz der Benutzung des Fly Henry PPG Meter entstehen. Eine Genehmigung zur Nutzung am jeweiligen Fluggerät, z.B. einem Paramotor kann nur durch den jeweiligen Motoren-/Rahmenhersteller erteilt werden. Durch unautorisierte Nutzung können unter Umständen die Betriebserlaubnis für das jeweilige Fluggerät oder Gewährleistungsansprüche erlöschen. Das Start Monitor System befreit den Piloten nicht davon einen Vorflugcheck durchzuführen sowie weitere vorgeschriebene Sicherheitsvorgaben einzuhalten. Der Käufer des Fly Henry PPG Meter übernimmt die alleinige Verantwortung für alle Risiken, die mit der Benutzung verbunden sind, einschließlich Sachschäden, Verletzung und Tod des Nutzers sowie Dritten.